Security Chimneys HE43-2 Instruction Manual

Manuel d’installationet d’utilisationCes instructions ont pour but de vouspermettre d’effectuer une installation simpleet sécuritaire du

63.2.6 Medium CombustionThis is the recommended mode of operating the BIS TRADITION CE and should be the onenormally used since it will deposit

73.2.9 Smoking – Causes and TroubleshootingTo reduce the likelihood of smoking when opening the door, set the combustion air controlsto the left befor

8IMPORTANT NOTESA. Do not block the hot air vents to the fireplace as this will cause the fireplace to overheat.B. Never start a fire using gasoline

93.3.3 Top Baffle Removal Prior to Cleaning The ChimneyBefore starting to clean your chimney, we recommend that you remove the top baffle to

103.3.7 Refractory ReplacementThe intense heat of the fire will normally cause hairline cracks in the refractory. Thesecracks can be min

113.3.9 Door AdjustmentThe door may need to be adjusted tobe completely airtight. The gaskets’air-tightness can be adjusted using theadjustment sc

123.4 FIREPLACE INSTALLATION3.4.1 Locating The BIS TRADITION CEA. The best location to install your fireplace is determined by considering the locatio

133.4.2 Hearth Extension RequirementsThe BIS TRADITION CE may be installed directly on a combustible floor; however, thecombustible floor in front of

143.4.3 Framing, Facing And MantelThe construction of the framing, facing, and mantel must be in accordance with the standardsand the following illust

15INSULATED CHASE CONSTRUCTIONFigure 11

25 YEAR LIMITED WARRANTY• Security Chimneys International Ltd. warrants to the owner of a Security Fireplace that the wood burning fireplace will

16FacingNote: The facade must be removable once installed. The facade isdesigned to overlap any facing material installed on the fron

17Figure 13b Figure 13c3.4.4 Fireplace BlowerThe fireplace comes equip

183.5 HOT AIR DUCTING INSTALLATIONDifferent hot air ducting systems can be installed with the BIS TRADITION CE :- Gravity kit- Forced air kit3.5.1 G

19The single outlet system is designed to be installed either flush with the front of the BISTRADITION CE or extended out slightly from the face of th

20The duct system must be installed respecting the following:1. Remove the top and bottom plates closing up the 8" dia. holes on top of the fire

213.5.2 Central Forced Air Kit (Not tested under EPA certification)The knock-outs provided on the back and on the sides of the BIS TRADITION CE allow

223.6 OUTSIDE AIRIt is mandatory to install an outside air connection to the BIS Tradition CE. The followingcomponents are required and are included w

234. THE CHIMNEY4.1 CHIMNEY INSTALLATION NOTES1. If possible, install an interior chimney as it will provide better performance. In areas withcontin

244.2 CHIMNEY INSTALLATION INSTRUCTIONS1. Cut and frame the holes in the ceiling, floor and roof where the chimney will pass (see figure 27).Use a pl

25AC CHIMNEY INSTALLATION(AIR COOLED GALVALUME CHIMNEY) Figure 30Note: Outsid

Details Of The 25 Year LimitedFireplace WarrantyYear 1:Parts and labour (no charge)(see on page for exclusions and conditions)Air control assemblyPla

26Figure 31Figure 32Table 2ROOF DOWN SLOPE HOLE SIZESLOPEASHT+ / HT6103+S-2100+ / HT6000+ACRoof Pitch6"6"6"0 *12 3/8" (314 mm)14 1

274.3 OFFSET CHIMNEY INSTALLATONThe minimum chimney height when using elbows is:Fireplace modelBIS TRADITION CEChimney modelASHT+ / HT6103+ / S-2100+

28Table 4ONE LENGTH BETWEEN ELBOWSTWO LENGTHS BETWEEN ELBOWSCHIMNEY6”ELBOWDEVIATION& HEIGHT8”12”18”24”36”48”8” & 48”12” & 48”18” & 48”

29Figure 33Figure 34

304.4 ANGLED WALL RADIATION SHIELD(RSM+, RSMI30, RSMI45)When traversing a combustible wall with the chimney at a 30º or 45º angle, an angledfirestop o

314.5 CHIMNEY SUPPORT INSTALLATIONUniversal Roof SupportThis support has three possible uses:1. For ASHT+ / HT6103+ and S-2100+ / HT6000+, it must be

32Figure 364.7 CHIMNEY ADAPTOR (S-2100+ / HT6000+)The fireplace is normally supplied with a chimney adaptor suitable for the ASHT+ /HT6103+ c

334.8 INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION WARNING: Before starting the installation, the masonry chimney must beinspected by a q

345. PARTS AND COMPONENTS LIST (AC Chimney)Description Part No.Lengths 6" dia.12" length AC 6L1218" length AC 6L1836" length AC 6L

356. OPTIONSGravity kit:Part No.:Complete double ducting system including: 2 elbows 90º,2 telescopic lengths, 2 grill supports and 2 black grills7B30Z

iiTABLE OF CONTENTSPage1. SAFETY RULES ... 12.

367. APPENDIXSPECIFICATIONSWeight 300 lbsHeight 36"Width 36"Depth 24 1/2"Chimney weight ASHT+ (6" dia.) : 6.25 lb/ft.Chimney weigh

11. SAFETY RULES FOR OPERATING YOURFIREPLACE MODEL BIS TRADITION CE• Use only a Security Fireplace glass door, specifically designed for t

22. CERTIFICATION LABEL

33. THE FIREPLACE3.1 INTRODUCTIONThe BIS TRADITION CE fireplace is an energy efficient, heat circulating, close combustionfireplace. You will rece

43.2 OPERATING THE BIS TRADITION CE3.2.1 FuelThe BIS TRADITION CE is designed to work best when fuelled with seasoned cordwood.Hardwoods are preferred

53.2.4 Primary Air and Air Boost ControlsThere is no flue damper in the BIS TRADITION CE. As is common with air tight stoves,the combustion air contr